The main difference is that the assembly for a lavatory-sink faucet includes a pop-up assembly that allows the user to open and close the drain. Remove your existing faucet, being careful not to damage the supply lines or sink. The faucet handle's front side contains cold and hot buttons. Widespread or split-set, which work with three-hole basins, but the spout and two handles come in three separate pieces. Step 1âGetting Started: Basic Precautions. Prices, Promotions, styles, and availability may vary. Homeowners can find faucets for $50 at a hardware store, but a quality product â such as bathroom sink faucets from Delta, Moen or Kohler â costs about $200, he adds. Once they’re off, open the faucet to drain any remaining water in the pipes. Follow the manufacturerâs directions and lay down a thin layer of sealant or putty right before you put in the faucet. Turn the 1 or 2 valves that you find clockwise to turn off the water. Next, disconnect the supply lines from the old faucet. Plastic gaskets generally snap onto the faucet, so be sure to seat them properly so the faucet is tightly sealed. Avoid tightening the nuts any further, or you could damage the sink. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted. Today I will be showing you how to replace a lavatory faucet. Wipe up any water that drips onto the bottom of the vanity immediately to prevent damage or warping. It’s a good idea to flush the new faucet and check for leaks before you’re done. The tools you'll need include: X Research source Adjustable wrench Basin wrench Bucket Towel Flashlight Measuring tape Plumberâs tape Sponge or scrubber Bathroom cleaner or soap Rag or cloth New fauâ¦ Hiring a professional to perform household maintenance may offer convenience and peace of mind, but you can do many of these jobs yourself with no experience or special tools. Start by turning off the water supply. Use the flashlight to locate the nuts under the sink if you're having trouble locating them. Once the hoses are attached to the new faucet, reattach them to the water supply. Then install the sink and connect the supply lines to the water valves. Installing the new faucet. Changing a bathroom-sink faucet is similar to fix a kitchen sink faucet. Of course, you have more options if your project involves also replacing the sink and countertop, in which case you can match the new faucet with whatever sink/countertop you choose. How to Install a Bathroom Sink Pop-Up Assembly Compression, ceramic, ball and cartridge type faucet designs all feature rubber O-rings. Our faucet is centerset. The cartridge water valve is a type of washer-less water control valve found in the kitchen or bathroom. If your sink has a lip that lays on the countertop, you have a drop-in. Connect the lift rod to the lift rod strap by pushing the button. When youâve tightened the nuts by hand, finish tightening them by turning them another quarter turn with the adjustable wrench if necessary. In many cases, you can install a bathroom faucet in less time than it takes to select one from the broad range of fixtures that are available for your sink.. Then rinse the area with clean water and pat it dry. You may use a small amount of plumber putty under the flange before placing it inside the sink. Itâs a good idea to flush the new faucet and check for leaks before youâre done. Start by wearing plastic gloves. Step 1: Identify Your Faucet Type. Gather your tools and supplies. Step 1. Removing the Old Faucet. If you have trouble locating the shutoff valve, you can turn off the water supply to the entire line running to the bathroom sink. You can have to turn the water supply valves in a clockwise direction until no water can drip. It is always better to replace them. Grab a flat head screwdriver and carefully apply pressure to the buttons' edges. How to Remove a Bathroom Sink Lever-Style Faucet Handle with No Screws or Cap: Step 1: Remove the Button. Place a shallow pan or bucket underneath the sink to catch any water. Move the faucet handle to ensure that the last drops of water are also drained out. Replace the stem into the valve seat, secure it with a screw. Check all the connections and retighten if needed. The number of holes in your sink or vanity top can influence the style of bathroom faucets you choose. Replacing an Undermount Sink 1 Cut through the caulk that connects the sink to the underside of the counter. Ensure the gasket is on the bottom of the new faucet, itâs usually a plastic part that is the same shape as the faucet base. Things we are going to be going over today are, remove a P-trap and pop-up drain. If you have a very old two-handle faucet, it may be a compression-type rather than a cartridge. Next, install the drain body and rubber washer through the top of the sink. First, take the faucet apart. When the faucet is accurately positioned at its place and pipe connections are at their respective holes, insert the washer and tighten the nuts with hands first and then with the wrench. Step 2. These four steps detail how to get rid of the old faucet. When replacing a bathroom sink faucet, the best strategy is to buy a new faucet that matches the hole configuration of the old faucet. Each faucet handle (hot and cold) has its own cartridge, a valve that turns with the handle to control the flow of water into the faucet spout. Turn the nuts by hand to the right (clockwise), then tighten them the rest of the way with the adjustable wrench. 1. Make sure that you purchase a faucet that matches the holes in your sink. Center-set, where there will be three holes in the sink and the one-piece faucet will have separate handles controlling the hot and cold water. Instructions. Put the gasket on first. This will protect your sink, vanity, and floors from leaks and water damage, and prevent water from spraying everywhere when you remove the faucet. 4. To tighten the nuts, turn them to the right (clockwise). Then run hot and cold water for one minute. June 29, 2017 / Written by: Josh Crank. Make sure you've removed any old putty from the sink with wet rags and a plastic putty knife first. The same steps apply if you're installing a new faucet onto a new sink. With a bucket handy, use an adjustable wrench to loosen and remove the flexible extension from the faucet. The buttons are very fragile, requiring you to get extra careful when removing or handling them. Mineral spirits can help remove old silicone sealant. Link to Lowe's Home Improvement Home Page. Product costs, availability and item numbers may vary online or by market. Before everything else, ensure the process starts with turning off the water supply lines. Insert the ball rod into the drain assembly and tighten the sleeve. If your faucet didnât come with a gasket, you'll need to apply sealant or plumberâs putty before installing the faucet. Welcome to the Take Charge of Your Home series from Direct Energy! Just remove the aerator. 2. Replacing a leaky or outdated faucet isn't as difficult as you might think. Replacing a bathroom sink valve is rather easy. Insert new faucet, tighten mounting nuts underneath and attach water supply tubes. How to Replace a Sink Faucet. Just remove the aerator. You may have to look underneath to be sure. To remove old sealant or silicone, dampen a sponge or rag with mineral spirits and wipe the area clean. Once youâve loosened the nuts with the wrenches, you can remove them the rest of the way by hand. 3. The cartridge water valve may come in a plastic or brass body. Then use an adjustable wrench to tighten the nuts. Remove the bathroom sink faucet handle. Place the faucet assembly through the mounting holes in the sink. 11 Replace the packing nut and gently tighten with a crescent wrench. Press this ring onto the rim of the opening in your sink basin. When you measure for bathroom sink faucets, you'll see two or three holes on your sink or countertop.The relevant measurement is the spacing between the centers of the outer holes. The labor cost to install or replace a kitchen, bathroom, or bathtub faucet is $45 to $150 per hour, with plumbers charging for an hour or two.Faucet prices alone average $100 to $350. Check all the connections and retighten if needed. Procedure: Replace Bathroom Faucet Cartridge . Turn on the bathroom faucet to relieve remaining water pressure. Next, insert the lift rod into the faucet. Replace the aerator, and youâre done installing your new bathroom faucet. Ð°Ð¼ÐµÐ½Ð¸ÑÑ ÑÐ¼ÐµÑÐ¸ÑÐµÐ»Ñ Ð² Ð²Ð°Ð½Ð½Ð¾Ð¹ ÐºÐ¾Ð¼Ð½Ð°ÑÐµ, consider supporting our work with a contribution to wikiHow, New faucet (purchased after you remove the original). Shut off the water supply. Hold the faucet in both hands and pull it straight out from the mounting holes. Our local stores do not honor online pricing. If the gasket is connected with the flange or drain nut, remove that first. Drain the remaining water into the bucket. Remove the nuts from underneath and take out the faucet. Removing the Old Bathroom Faucet Cartridge. Before you start any sink repair, itâs important that the water supply be shut off. Mike Larson, general manager of Norblom Plumbing in St. Paul, Minnesota, charges around $150 to $200 for labor. 2 Push the new sink drain into the opening and onto the putty. If you want to replace your old faucet with a new kind, you'll have to replace the basin as well. Repairing a sink faucet is not as difficult as most people expect because, in the majority of cases, the problem is simply a worn-out gasket or washer. Locate the main water supply valve that is usually located under the skin. Speaking of sinks, you’ll either have one, two or three holes. First the basics, bathroom sinks come in two basic configurations, drop-ins and under mounts. Usually, you’ll find the valves underneath the sink. If you’re installing a new vanity and sink, it’s much easier to mount the faucet before you put the sink in place. Once youâve removed the supply lines, nuts, and washers, the faucet will be loose. Replacing a bathroom faucet is a straightforward job, but it does require a few tools that you'll need to remove the old faucet and install the new one. Depending on your plumbing, you may have a single water valve for the entire faucet, or you may have two separate valves for the hot and cold water. Disassemble the Faucet. Prices and availability of products and services are subject to change without notice. How to Replace a Bathroom Sink Drain Many bathroom faucet replacement kits include new drains, so take this opportunity to replace the drain pipe. Switch off the water valve under the sink. You can often identify the spacing just by looking, but if not, stretch a tape measure between them: Remove the gasket if there is one and set it aside with the faucet. Installing the new water supplies. Reach into the sink from above and run the blade of a utility knife through the bead of caulk, all the way around the rim of the sink. Most bathroom faucets that have two handles are cartridge-style faucets. Replace the aerator, and you’re done installing your new bathroom faucet. You can also lay a garbage bag down under the towel for even more protection, or in place of the bucket. Before setting the sink into place, connect the supply lines to the faucet shanks. Snap a photo of the plumbing to help with reconnecting later. Close the drain and place a towel in the sink to protect the surface and catch any dropped parts. It’ll either be centerset or widespread. Most of the faucets come in partially assembled drain. Theyâre often located in a cabinet beneath the sink. Pick the new faucet and place it over the holes of the sink where you placed the gasket. Before you can install your slick new bathroom faucet or kitchen faucet, you need to remove the old one. Secure it with the lock nut. Remove the drain nut from the flange.